aeForce™ EasePA12-CF is specially developed for FDM 3D printing process, and its substrate material is PA12 long-chain nylon, which has low density, low moisture absorption, high strength, high abrasion resistance, excellent chemical resistance and high heat resistance.
It also has good dimensional stability, no warpage and no shrinkage during the printing process, and can be used with aeSupport™ S-Multi Quick-Remove Support material to solve the problem of poor molding effect on the support surface of complex models.
Diameter: 1.75mm / 2.85mm
Net weight: 500g / 1kg / 2.5kg
DLC Hardened Steel Nozzle
Hardened Steel Nozzle
Recommended Hotend：Dragon series / Dragonfly series
|Property||Testing Method||Typical Value|
|ISO 1183||1.09 g/cm³|
|ISO 62:Method 1||0.6%|
Determination of temperature
|ISO 75: Method A||102°C (1.80MPa)|
|ISO 75: Method B||124.6°C (0.45MPa)|
|65.53 ± 0.98 MPa|
|Young’s modulus(X-Y)||3317.69 ± 55.41 MPa|
|Elongation at break (X-Y)||3.33 ± 0.17 %|
|Bending strength (X-Y)|
|103.13 ± 1.46 MPa|
|Bending modulus (X-Y)||3340.15 ± 259.26 MPa|
|Charpy impact strength （X-Y）||ISO 179||9.58 ± 0.70KJ/㎡|
|Tensile strength (Z)||ISO 527||38.76 ± 1.05 MPa|
|Young’s modulus (Z)||1694.0 ± 77.48 MPa|
|Elongation at break (Z)||4.25 ± 0.45 %|
Specimens printed under the following conditions: Nozzle temp 320°C, Bed temp 80°C, Print speed 45mm/s, Infill 100%, Infill angle ±45° Post-processing: 100°C Annealing 8 hours
Recommended printing conditions
|Recommended Nozzle Diameter||0.4-1.0mm|
|Recommended build surface treatment||PEI or Coating with PVP glue|
|Build plate temperature||60-80℃|
|Raft separation distance||0.08-0.12 mm|
|Cooling fan speed||Off|
|Print speed||30-90 mm/s|
|Retraction distance||1-3 mm|
|Retraction speed||1800-3600 mm/min|
|Recommended support material||aeSupport™ S-Multi Quick-Remove Support|
1. Nylon material is very easy to absorb moisture within the environment, and printing after absorbing moisture will result ozzing, extruding with bubbles and rough surface appearance, thus reducing print quality. It is recommended that put the filament into a dry box (humidity below 15%) immediately after opening the aeForce™ EasePA12-CF vacuum foil bag for printing. Please put the unused filament back into the original aluminum foil bag for sealed storage.
2. After the material is damp, there will be more printing ozzing, bubbles extruded and rough printing surface. Please dry the filament in an oven at 80-100 for 4-6h to restore the printing quality of aeForce™ EasePA12-CF.
3. It is recommended to use hardened steel and above grade nozzles made by Phaetus, which can effectively improve the print quality. Besides, it is recommended that the thickness of the heating block is longer 12mm.
4. After the printing is completed, the aeFocre™ printed part can be annealed to further improve the strength of print part. Annealing conditions: leave printing part in an oven at 80-100 for 4 to 8 hours and cool to room temperature naturally.
Extrusion Force vs Print Speed Test
Test parameters: 12mm length brass heat block, BMG extruder, Phaetus Hardened Steel Nozzle, Nozzle size 0.4mm, Layer Height 0.2mm.